Opinion Cars

To repair the shaft, remove it from the vehicle. Unscrew the clip seal splined connection, straighten her first in places where it was produced kernenie, and move in the direction of the pipe seal. With the help of an indicator, measure the radial clearance slot "cardan" two planes (perpendicular) at 7-8 cm from the end of the fork slots and fix its value. Permissible shaft runout after the edits must be a maximum of 0.6 mm at any place along its entire length. Crossings should be changed if: Bore than 1.6 cm on the cylinders are visible longitudinal indentations; heavily worn neck crosses at the installation site seal. If damage or wear of the working edges, seals, replace the end seals. The same applies to the needle bearings, if deformed or lost one of the needles, or they swing on the cylinders. Replace the developed parts of the compound (spline) "cardan" when the radial clearance in the slots becomes more 0,13-0,15 see Worn plugs should be replaced if the hole for the bearing has a diameter over 3 cm, or between planes ears fork length exceeds 6 If you see damage or wear rubber or felt ring, replace them. Change the shaft in case of breakage or wear of its individual parts. Without balancing driveshaft may be replaced with a cross in the set, only if there is no vibration. Propeller shaft assembly. At the end of the slotted "cardan" install everything in reverse order of removal. Before you collect the splined connection, felt ring lubrication necessarily saturate and do not forget to lubricate the splines. Collect splined connection needed so that the forks "cardan" were in a common plane with the deviation within 5 degrees. To do this, combine the labels (arrows) established before disassembly. Further, failure to screw the clip into two locations (opposite) and zakernite so that the perimeter of the cage a few curved to the side grooves moving fork. Fork pivot and cross check so that the nipples of slots and crossing, located near the bridge, located in one plane, and press nipple cross the other end of the shaft - a quarter turn against the clock. arrows, if observed by the axle gear. Securing the crossbar with a fork in a vise, zapressuyte glasses in the eye of bearings (needle). In this case, make sure that workers are not wrapped edge seals gaskets bearings. In the cup grooves check snap rings. Cardan joint the other end of the shaft is going the same way. Before assembly, lubricate the hinges with grease. Just fill each bearing grease on half of its volume. Gathering "cardan", check whether it is easy to move the fork pivot. There should be no jamming, forks should move freely by hand. Angular displacement for each joint should not exceed the value of 0,3 mm (recommended value of 0.023 cm) of torque at 10-12 kg / m at a radius of 35 millimeters. If you decide to open a beauty salon, you probably need quality equipment. Inexpensive Car equipment you can buy the company "Ode to service." Experienced professionals can help you choose the right equipment.

Given the tightening of requirements for toning cars, as well as increased interest in his services, road patrol, many motorists are removed dubbing the film from the glass. There are two ways rastonirovaniya car windows - in person or at a service station. Of course, inside the wizard, do rastonirovanie car windows very quickly, freeing you from all trouble, but their services will cost you just do not come cheap, yet this work is well under the force of every motorist. Some motorists believe that the exercise rastonirovanie car windows with his hands quite that easy, you just have to catch a film with a knife, and it has no problems "spoiled" by the glass. However, dubbing the film attaches to the glass with very strong adhesive, which greatly complicates the process rastonirovaniya glasses. But if you are enthusiastic and willing to perform the procedure on rastonirovaniyu car windows with his hands, then this article is for you. For that, you should stock up on: - a ruler or credit card payment (must be something fairly thin plastic products). - A clean cloth towel or newspaper. - Detergent or rubbing alcohol and warm water. All this is necessary in order to wash off the glue. Give clear guidance on the application of certain means are very difficult, because in each case may be nuances. If the tint did not very long ago, no more than three years ago, the removal of the film is simple enough warm water, and if earlier - in this case have to try and try different cleaners. That's all you need for this simple process. Nothing extraordinary, all you need is in each sector. If dubbing the film stuck very long time, then rastonirovaniya glasses require building a hairdryer, a typical home is not suitable, since its power is quite small. Before you remove the dubbing a film, be sure to thoroughly warm up the glass. To heat the film is recommended to use a hairdryer construction, have a greater capacity and ability to quickly heat the film. When heated to monitor air temperature, so that it did not reach 40 degrees, otherwise you risk melt dubbing the film, which greatly complicate its removal. Carefully heat a small portion of the film, but do not remove immediately. Aim the dryer only to the film, otherwise under the influence of hot air to glass or plastic and rubber parts will crack. If you properly remove the film, the glue will remain on dubbing the film, the glass also will be clean. To remove adhesive residue, use detergents for cleaning glasses. Many motorists use rubbing alcohol or clean with warm soapy water. Full clean glasses on the adhesive easier to navigate after the removal of glass from the car, also working with the filmed glass, you eliminate the likelihood of damage to the exterior and interior car. Although it is not necessary to dismantle the glass, if you act very carefully. It has long been known that much easier to remove the high-quality dubbing the film, as if to catch her and pull, it will come down one piece. Rastonirovanie glasses coated with cheap dubbing the film is more complex, because this film is easily torn, separated by parts, and requires more energy from your side.