Opinion Cars

SUVs are still important in this area, but people are downsizing to more fuel efficient SUVs instead. We are still stocking with the idea that it may go either way. Hoping for the best, but prepared for anything.

The serviceability of any vehicle depends on one of the most important components of fuel injection - fuel injectors. Since the engine fuel system is quite sensitive device, according to this she was the first crashes, when you receive a low-quality fuel, which contains a variety of impurities, whereby the manufacturer increases the octane number. In combustion of impurities on the inner and outer surfaces of nozzles formed tar deposits. Deposits in the form of lacquer peel brown-black, do not dissolve gasoline. If there is a dedicated device for cleaning the injectors, then, in principle, it does not make much effort. But since such an attitude is not at all, it is manual cleaning. Initially to replace oil. To do this you must have the compressor or pump, a special fluid that is used to clean the carburetor, rubber hose, it should approach the nozzle, and to consolidate its use plastic cable ties; pliers and a screw. After preparing the instrument must be removed from the fuel pump fuse, and then start the car, wait until he stall, and then pour fuel. Then carefully unscrew that pipe, which supplied fuel injectors. Once the tube is removed, you need to unscrew the pipe and remove the nozzle. Terminals injectors are disabled. Hole formed on the engine, locked, that would not hit the dust. When the hose is removed, you can completely drain the gasoline. Nozzle pulled out of the bar after the removal of fasteners. Careful examination of the rubber gasket held in order that would detect damage. As the car drives for a long time, it requires cleaning nozzle from the outside. This can be done with a brush. Followed by cleaning the inside. To this end is screwed into the filter nozzles from a prepared screw, clamping pliers, hanging out in different directions, but accurately, and to be removed. That now has the opportunity to begin cleansing itself inside the nozzle. You should begin with the accession of the hose to the nozzle. The next step is fixing it with a plastic strip to prevent a situation where he could fly. After that, using a can of cleaning fluid, sprinkled with output nozzle. To this end, the liquid is poured into the hose. This hose is attached to a compressor or pump. Best this can be done using a tight cap. The compressor can be switched on only very gently, without letting go of the hose. If pressure is good, then the opening in the nozzle, will be published washing fluid. Serve liquid need so much time, until it begins to vypryskivatsya uniformly, even spraying and measured flows. Such signs will indicate that the holes are clean well. Such an operation must be repeated with all the other jets. After finishing all the procedures for cleaning, start-to-assemble. To begin insert filter back into the nozzle, thus anchoring it very inscrutable, that is dense. Further, the nozzle must be cleared to put in place. Before you install everything back, you need to complete the entire mechanism lubricated with a special drug that buy is not difficult. In the next step nozzle crank until it stops in different directions.

Wheel Alignment wheels. What is the convergence of wheels? Words such as convergence and the breakdown is usually all mentioned together, but, in general, they mean different things. These words are used when talking about the operation associated with the adjustment and customization of automotive suspension. Setting the right angle to the axis of the leading wheels of the car is at the heart of the action. When you look at your car in front, you may notice that the front wheel axis deviated a bit out from the vertical for a couple of degrees. In the case where the wheels placed parallel to each other, the helm will be far harder. If the car is installed power steering, this effect is not so significant for you. For each wheel camber should be the same (may be small deviations), otherwise in motion the machine will go away. Convergence is the same, but when viewed from above the car. The front edge of the wheel after the collapse of the similarity should be directed inwards. All of this is the convergence of the wheels, plus some details of the provisions of the wheels and axles the car. Which requires adjusting the alignment? The first - is to improve exchange rate stability, ie, that the car is not thrown to the side (try to let go of the wheel on a straight road, and then you will understand). Second - this in order to make the car easier to manage, increase agility and reduce the chances of skidding. And the third - to more economical use of the rubber. When you keep that setup, which is designated plant manufactures a car, you provide a safe and comfortable driving. Tight control, a weak or inaccurate response to the helm may be due to misalignment. With proper adjustment of similarity between the collapse of good you can save! When misalignment is greatly increased tire wear and fuel, as well as accelerated wear podvesochnyh nodes. When properly installed corners new tires wear out within a month. From the effects of friction, they are erased in one place more rapidly than in others. How often are required to carry out adjustment of similarity of the collapse? For our cars is required to be made every 10-15 thousand miles. Foreign cars can hold up to 30,000. When adjusting the similarity of the collapse of each year you will be able to extend the work of tires and some suspension parts. It will save you money. In some cases, you have to make an unscheduled descent-collapse: If you are driving along a large pit, was hushed up drive wheels. If you have recently had repair the undercarriage. Once clearance has been modified car. If the car begins to lead the side. If the new tires wear out quickly. With poor steering return to its original position when you exit the turn (if you do not twist the steering wheel in position, but simply let them go, the wheel itself should return to its original position). When you move through the curb or on your way met a deep pothole, then you need to check the similarity of collapse, or soon you will find a quick tire wear, which is why you will have to wait for the premature replacement of tires. Many of the causes that are associated with problematic governance, for example, poor steering response and its withdrawal in the other direction can be determined only after checking the similarity of the collapse.

Given the tightening of requirements for toning cars, as well as increased interest in his services, road patrol, many motorists are removed dubbing the film from the glass. There are two ways rastonirovaniya car windows - in person or at a service station. Of course, inside the wizard, do rastonirovanie car windows very quickly, freeing you from all trouble, but their services will cost you just do not come cheap, yet this work is well under the force of every motorist. Some motorists believe that the exercise rastonirovanie car windows with his hands quite that easy, you just have to catch a film with a knife, and it has no problems "spoiled" by the glass. However, dubbing the film attaches to the glass with very strong adhesive, which greatly complicates the process rastonirovaniya glasses. But if you are enthusiastic and willing to perform the procedure on rastonirovaniyu car windows with his hands, then this article is for you. For that, you should stock up on: - a ruler or credit card payment (must be something fairly thin plastic products). - A clean cloth towel or newspaper. - Detergent or rubbing alcohol and warm water. All this is necessary in order to wash off the glue. Give clear guidance on the application of certain means are very difficult, because in each case may be nuances. If the tint did not very long ago, no more than three years ago, the removal of the film is simple enough warm water, and if earlier - in this case have to try and try different cleaners. That's all you need for this simple process. Nothing extraordinary, all you need is in each sector. If dubbing the film stuck very long time, then rastonirovaniya glasses require building a hairdryer, a typical home is not suitable, since its power is quite small. Before you remove the dubbing a film, be sure to thoroughly warm up the glass. To heat the film is recommended to use a hairdryer construction, have a greater capacity and ability to quickly heat the film. When heated to monitor air temperature, so that it did not reach 40 degrees, otherwise you risk melt dubbing the film, which greatly complicate its removal. Carefully heat a small portion of the film, but do not remove immediately. Aim the dryer only to the film, otherwise under the influence of hot air to glass or plastic and rubber parts will crack. If you properly remove the film, the glue will remain on dubbing the film, the glass also will be clean. To remove adhesive residue, use detergents for cleaning glasses. Many motorists use rubbing alcohol or clean with warm soapy water. Full clean glasses on the adhesive easier to navigate after the removal of glass from the car, also working with the filmed glass, you eliminate the likelihood of damage to the exterior and interior car. Although it is not necessary to dismantle the glass, if you act very carefully. It has long been known that much easier to remove the high-quality dubbing the film, as if to catch her and pull, it will come down one piece. Rastonirovanie glasses coated with cheap dubbing the film is more complex, because this film is easily torn, separated by parts, and requires more energy from your side.

Painting cast wheels rukamiSo their time covering cast wheels tarnish the paint loses its factory appearance. This article was written to help those who are not happy with the status of their CDs, the paint which has lost its former luster, and money for new wheels you do not. Her goal - to tell, both independently with minimal cash outlay, painted alloy wheels and restore them to youth. For a start Take your hands and wear rubber gloves. Now take the disks and follow them carefully mine. When washing, you can use simple household tools: powder, an old sponge, for penetration into hard to reach places you can take an ordinary toothbrush. If something is rubbed with difficulty, such as places with dust from brake pads, then take any cleaner containing acid - it can easily cope with this filth. After cleaning the disc scratches and other defects that become more evident. Scrapes on the rims can be eliminated in the following ways, choose: - a file, rather tough and radical method - sandpaper with a fine-grained, rather dreary exercise, take a long time - The best way to grinding - drilling machine, if you happen to have a sim miracle tool - certainly use it! You can also combine all the above mentioned methods, ranging from the "rough" and ending with "soft". Handle all the defects, remove chipped paint with sandpaper, grind the end it all a drill. Do not be afraid to remove too much of the old paint, primed with all the consequences will be ustraneny.Kogda you polished wheels properly and you are satisfied with their appearance, clean them from dust and degreased. Degrease they can be absolutely any solvent: acetone, "White Spirit" and even a means for removing with nail polish. Now, after a complete cleaning, we must find a place where, in fact, we proceed to the main - priming and painting. You can use a simple bucket, of course, if you are not lying around the house a special berth for coating disks, which is hardly possible. Primer. One liter cans should be enough for all four discs. Gruntuem tripled. After drying, one coat before applying the next grind bumps. You can use the good old sandpaper or some coarse cloth. Painting. There may be difficulties, most importantly the right to follow the instructions. The ideal distance for the spray cans of paint is about 50-70 centimeters. Again plot the three layers, between which produces grinding. Polishing is best soaked in water nulevkoy. Varnished. Here we reach the final stage of the return of the factory gloss cast disks. It will take two or three banks. Luck also be applied in three layers and also with an intermediate grinding with moistened nulevki. Thus, we have saved on buying new cast wheels and expensive painting in the old service center, as well as purchased, no doubt, a valuable experience that can be useful in the future. And now rather run and try on the updated drives your darling! Good luck!

Engine heater requires each vehicle to easily lead into any frosty winter. You can buy factory heater and install it on your car, but if you do not have enough money to plant or do you want to do with their hands engine heater you need special skills and materials. In order that would make a good heater with your hands, you will need these components. 12 mm Gun sleeve, Candle Warmer, relays, copper wire and maybe this will be enough. First of all you will need to drill a hole in the side pocket in the bottom of the well will need to make a hole, which is threaded for candles. After that sleeve is attached to the suction nozzle. Such a design is set in a tank car, and it provides the wire with a voltage of 12 volts. The operation of this self-made heater is that the candle set in the sleeve is energized, which gradually heats it, and she has a candle heats the fuel in the tank car which comes in a sleeve through the suction port. After installing such a system, you can not worry about what your car will not start at a low temperature. Now you are in any case be able to make your car even if the street bude temperature below 30 degrees. In the case where the temperature is very low try to start your car, not including this system as well as for frequent use and not too low temperature, it can break down. To protect this system, using protective materials that are manufactured on the dress design. Before you run a homemade heater must be very careful to check it, he should be very clearly and accurately operate. Such a heater should not be used with water, place it only in combination with antifreeze. Thoroughly check the cooling system it should be no precipitate. Heater may include not only when the engine is running, because otherwise it may happen after the failure of which to rebuild your engine will be very expensive and time consuming. For whatever mistakes and no reason not reparable damage to your car to follow certain safety rules. If your car is installed V-twin engine then you need to install the heater on both sides, it will allow more efficient operation of the heater and will soon make your car even at very low temperatures. At close approach, and proper execution of all work for the production of engine heater, you can produce quality and reliable heating system with their own hands, and she in turn will enable you to easily start your car in any weather. When installing the system be very careful and attentive it will allow you to avoid some or errors.

The idea of ??every car enthusiast who likes to spend time upgrading my car, wants to wants to give your car unique. Tuning is generally considered a matter of troublesome, but when the result exceeds all expectations, then spent it already does not care. For those who have not yet faced with the installation of sound system in the car, it is necessary to clarify that midbasa at the front podium - is the main part of the entire audio system. In this case we are interested in installing a podium in a car VAZ 2114. The challenge for playing high-quality sound, you need to install the speakers at the correct angle. To this end, the entire area of ??the wooden podium will be deposited makrofleks, and then he pasted frame with glass. Materials for making the podium will need the following materials: plywood, 8 mm thick with an area of ??0.8 sq. m. thick cardboard hardboard fiberglass thickness of 0,25 mm and an area of ??2 square meters, uglelenta epoxy putty EHP polyester with glass emery cloth with a rubber holder cutter plasticine PVA glue spray makrofleksa screws nails rubber gloves Safety work should be performed in thick rubber gloves. Work to determine the size of a podium carved layout of the paper. Then, focusing on the layout of plywood with the cutter sawed the bottom of the podium, the range for the most dynamic and lateral struts on which it will be fixed. In order for the final assembly of the podium was easier to customize the details of the size, preferably all components of the cut immediately in duplicate. Then, using PVA glue and nails, he is going to the podium. The inner diameter of the ring to do with the stock and let it be outside butt. Pocket can be drunk from plywood, and you can use already available. It should be just unscrew from the hull and podpilit that it accurately adjoined to the bottom of the podium. The whole construction fill makrofleksom. Layer should be thin, otherwise it will be a long time to dry. After drying process the outer layer: First, cut away all the excess and then oshkurivaem and the podium is almost ready. Now combine the frame at the base of the whole area. To do this, cut out of hardboard one additional item, the so-called rear panel. If this item is missing, try to increase the thickness by means of thick cardboard. Attach the resulting "flat" to the plywood with glue PVA .. Then, using putty and a putty knife to give details of the status of a whole. Again, wait until dry and again oshkurivaem medium grit sandpaper. Before installing ready-made podiums can be painted or vinyl obtyanut and the work is completed. Despite the result that the finished equipment VAZ 2114 does not imply the existence of a powerful speaker system, with adequate tools and imagination, a Russian man will not give in to the seeming at first glance, a daunting task. The owners of domestic cars will always find a way out and from the car will be heard loud music.

Edging doors of your vehicle is fully applicable to the changes that have impacted positively on the aesthetic rather than functional status of the car. This is done primarily to please the eye motorist, and of course those who are in the car. Often lining car doors make for increased noise insulation properties. At first glance it may seem that most sheathe the door - still quite quick and simple thing, but it is not so. After all, no wonder there are so many services that deal with skin. Attach to a standard door and sticking a piece of it - is far from meaning to sheathe the door. However, to assert that sheathe the car door with his hands, too, should not be impossible. This process will require you to have enough free time, the necessary materials, tools and, of course, a creative approach that would make some kind of punch line, a piece that makes your car does not look like their brothers of iron. It is the latter features a trim doors with his hands on the same process in a specialized studio or service, even a very elite. For covering the door is most commonly used leather, whether it be a natural material or a good substitute. The most essential feature to be selected for cladding material - sufficient ductility, it is necessary to avoid not want wrinkles and sagging skin. Also, care must be taken and the presence of foam, if you certainly want to improve the sound insulation upgraded doors. Of course, you will need glue, which also requires little choice - the glue should not eat the skin, and especially the foam. Often on the casing of the door thinking motorists who purchase a powerful sound system. The question arises as to place correspondingly more powerful speakers in the doors, usually the front. For this we have apart cladding material to prepare the material of which will be made the podium for the speaker, most often in this role serves thick plywood or particle board. To facilitate the construction of manufactured catwalk to drill a large number of holes that would not affect the structural strength. To not make the podium entirely of wood (it is very difficult and time consuming) use construction foam, which is applied in the framework of the podium, and after it dries cut it too much quantity, grind. Thin plywood or hardboard is not suitable, since they are prone to various changes in form, whether bending or swelling. It certainly will affect the appearance of the date of the car's interior, and, exactly, no one is happy. So far one of the key values ??is the quality of select materials. Perhaps this is the most crucial moment, as in the preparatory work and in the skin of doors in general. Job of covering the doors in the home (garage) conditions, it is more convenient to hold together, because often there will be a need for something to hold, tighten, fix, and so on. We should not forget that not everything can happen at once and, ideally, be patient. The adage about the first pancake is not born from scratch. However, about the fact that nothing is impossible to forget, too, should not be.