Opinion Cars

Painting cast wheels rukamiSo their time covering cast wheels tarnish the paint loses its factory appearance. This article was written to help those who are not happy with the status of their CDs, the paint which has lost its former luster, and money for new wheels you do not. Her goal - to tell, both independently with minimal cash outlay, painted alloy wheels and restore them to youth. For a start Take your hands and wear rubber gloves. Now take the disks and follow them carefully mine. When washing, you can use simple household tools: powder, an old sponge, for penetration into hard to reach places you can take an ordinary toothbrush. If something is rubbed with difficulty, such as places with dust from brake pads, then take any cleaner containing acid - it can easily cope with this filth. After cleaning the disc scratches and other defects that become more evident. Scrapes on the rims can be eliminated in the following ways, choose: - a file, rather tough and radical method - sandpaper with a fine-grained, rather dreary exercise, take a long time - The best way to grinding - drilling machine, if you happen to have a sim miracle tool - certainly use it! You can also combine all the above mentioned methods, ranging from the "rough" and ending with "soft". Handle all the defects, remove chipped paint with sandpaper, grind the end it all a drill. Do not be afraid to remove too much of the old paint, primed with all the consequences will be ustraneny.Kogda you polished wheels properly and you are satisfied with their appearance, clean them from dust and degreased. Degrease they can be absolutely any solvent: acetone, "White Spirit" and even a means for removing with nail polish. Now, after a complete cleaning, we must find a place where, in fact, we proceed to the main - priming and painting. You can use a simple bucket, of course, if you are not lying around the house a special berth for coating disks, which is hardly possible. Primer. One liter cans should be enough for all four discs. Gruntuem tripled. After drying, one coat before applying the next grind bumps. You can use the good old sandpaper or some coarse cloth. Painting. There may be difficulties, most importantly the right to follow the instructions. The ideal distance for the spray cans of paint is about 50-70 centimeters. Again plot the three layers, between which produces grinding. Polishing is best soaked in water nulevkoy. Varnished. Here we reach the final stage of the return of the factory gloss cast disks. It will take two or three banks. Luck also be applied in three layers and also with an intermediate grinding with moistened nulevki. Thus, we have saved on buying new cast wheels and expensive painting in the old service center, as well as purchased, no doubt, a valuable experience that can be useful in the future. And now rather run and try on the updated drives your darling! Good luck!

Engine heater requires each vehicle to easily lead into any frosty winter. You can buy factory heater and install it on your car, but if you do not have enough money to plant or do you want to do with their hands engine heater you need special skills and materials. In order that would make a good heater with your hands, you will need these components. 12 mm Gun sleeve, Candle Warmer, relays, copper wire and maybe this will be enough. First of all you will need to drill a hole in the side pocket in the bottom of the well will need to make a hole, which is threaded for candles. After that sleeve is attached to the suction nozzle. Such a design is set in a tank car, and it provides the wire with a voltage of 12 volts. The operation of this self-made heater is that the candle set in the sleeve is energized, which gradually heats it, and she has a candle heats the fuel in the tank car which comes in a sleeve through the suction port. After installing such a system, you can not worry about what your car will not start at a low temperature. Now you are in any case be able to make your car even if the street bude temperature below 30 degrees. In the case where the temperature is very low try to start your car, not including this system as well as for frequent use and not too low temperature, it can break down. To protect this system, using protective materials that are manufactured on the dress design. Before you run a homemade heater must be very careful to check it, he should be very clearly and accurately operate. Such a heater should not be used with water, place it only in combination with antifreeze. Thoroughly check the cooling system it should be no precipitate. Heater may include not only when the engine is running, because otherwise it may happen after the failure of which to rebuild your engine will be very expensive and time consuming. For whatever mistakes and no reason not reparable damage to your car to follow certain safety rules. If your car is installed V-twin engine then you need to install the heater on both sides, it will allow more efficient operation of the heater and will soon make your car even at very low temperatures. At close approach, and proper execution of all work for the production of engine heater, you can produce quality and reliable heating system with their own hands, and she in turn will enable you to easily start your car in any weather. When installing the system be very careful and attentive it will allow you to avoid some or errors.